Hiperface DSL encoder cables

There are basically shielded and unshielded cables available.

At cable lengths, less then 200 mm, inside the motor, it is possible to use unshielded cables.

At cable lengths, above 200 mm, inside the motor, we suggest to use shielded cables.

• Variances of unshielded cables
• • Length of the cable
  • Diameter and size of the heat shrink at the connector
  • Amount of wires (2 or 4)
• Variances of shielded cables
• • Length of the cable
  • Type of shield connection (strain relief, extra grounding wire, shield on pin 4)
  • Variances of the cable exit (Motor connector side)

The Hiperface DSL wires are on pin 2 and pin 3

Pin 4 is used at the EKS36 / EKM36 as shielding contact

Pin 1 and pin 4 is used at the ENS35 / ENM35 for the temperature sensor

Overview pin assignment:

• DOL-0B02-G0M2XC1 (2062083)
  ​Cable (200mm) without shielding/jacket, with heat shrink at the connector
  ​Diameter (heat shrink): 3.7 mm
  ​Length (heat shrink): 70 mm
  ​The cable is designed for the EKS36 / EKM36
  ​
• DOL-0B02-G0M3XC1 (2091818)
  ​Cable (300mm) without shielding/jacket, with heat shrink at the connector
  ​Diameter (heat shrink): 3.7 mm
  ​​Length (heat shrink): 70 mm
  ​​The cable is designed for the EKS36 / EKM36​
  ​
• DOL-0B02-G0M4XC1 (2086286)
  ​Cable (400mm) without shielding/jacket, with heat shrink at the connector
  ​Diameter (heat shrink): 3.7 mm
  ​​Length (heat shrink): 70 mm
  ​​The cable is designed for the EKS36 / EKM36
  ​
• DOL-0B02-G0M2XC2 (2079920)
  ​Cable (200mm) without shielding/jacket, with heat shrink at the connector
  ​​Diameter (heat shrink): 2.8 mm
  ​​Length (heat shrink): 25 mm
  ​​The cable is designed for the EFS50 / EFM50

• DOL-0B04-G0M2XC1 (2058333)
  ​Cable (200mm) without shielding/jacket, with heat shrink at the connector
  ​Diameter (heat shrink): 3.8 mm .. 4.2 mm
  ​​Length (heat shrink): 70 mm
  ​​The cable was designed for the EKS36 / EKM36 with 4 wire DSL (which is phased out)
  ​
• DOL-0B04-G0M4XC1 (2076293)
  ​Cable (400mm) without shielding/jacket, with heat shrink at the connector
  ​Diameter (heat shrink): 3.8 mm .. 4.2 mm
  ​​​Length (heat shrink): 70 mm
  ​​​The cable was designed for the EKS36 / EKM36 with 4 wire DSL (which is phased out)
  ​
• DOL-0B04-G0M2XS10 (2140378)
  ​​Cable (200mm) without shielding/jacket,
  ​​​The cable was designed for the ENS36 / ENM36 with has the temperature sensor on pin 1 and pin 2

• DOL-0B02-G0M3AC2 (2108944)
  ​Shielded cable (335 mm) with shield connection at the strain relief.
  ​Designed for the EDx35, EEx37
  ​
• DOL-0B02-G0M2XS09 (2092832)
  ​Shielded cable (300 mm) with heat shrink at the connector.
  ​The cable has a grounding wire (70mm) with a cable shoe, connected to the shielding
  ​
• DOL-0B02-G0M2XS02 (2104097) -> customized
  ​Special shielded cable (260 mm) with heat shrink at the connector and a special pin outlet
  ​The cable has a grounding wire (70mm) with a cable shoe, connected to the shielding​
  ​
• DOL-0B02-G0M2XS01 (2104098) -> customized
  ​​Special shielded cable (210 mm) with heat shrink at the connector and a special pin outlet
  ​​The cable has a grounding wire (70mm) with a cable shoe, connected to the shielding​
  ​
• DOL-0B02-G0M2XS04 (2108599) -> customized
  ​Special shielded cable (370 mm) with heat shrink at the connector and a special pin outlet
  ​​​The cable has a grounding wire (70mm) with a cable shoe, connected to the shielding​
  ​
• DOL-0B02-G0M2XS05 (2110386) -> customized
  ​Special shielded cable (370 mm) with heat shrink at the connector and a special pin outlet
  ​​​​The cable has a grounding wire (70mm) with a cable shoe, connected to the shielding

• DOL-0B03-G0M4XC1 (2087314)
  ​Shielded cable (430 mm) with shield connection on pin 4 of the connector.
  ​Designed for the EKS36 / EKM36 with GND on Pin 4 (hardware "B" and later)

• YFJSA4-010EG1MMIA8 (2117790)
  ​For the PGT-13-S
• DSL-1202-G01MA (2061361)
  ​For the PGT-11-S